Search Results

With the advent of low evaporative emission requirements there has been the rapid adoption of multilayer extrusion technology into the production of Fuel and Vapour tubing used on Fuel systems on automobiles. Multilayer extrusion technology enables a manufacturer of Fuel and Vapour tubing to simultaneously co-extrude dissimilar thermoplastic materials in tubular form. This allows the manufacturer to combine expensive and brittle high performance evaporative emission ‘barrier’ polymers with lower cost engineering polymers. However, it is a well-known characteristic of these multilayer tube constructions that the joints between them and connector ‘barbs’ have lower joint integrity. Joint integrity is most often quantified by ‘Pull-off’ and leakage tests. Recent developments in LEV-II requirements for 2004 and beyond indicate that joint integrity will become a focus area for study and improvement.

Consideration of the approaching ‘energy crisis’ reveals two requirements for future light duty automotive engines. 1) maximum economy and 2) the ability (perhaps with detail design re-optimisation) to accept a range of fuels of petroleum or other extract, of differing ignition characteristics. One combustion system which meets these requirements is the MAN ‘FM’, the potential of which has already been demonstrated in truck-size engines but on which little information has been published in light-duty engine bore sizes. The paper describes both design and experimental work carried out to evaluate the application of the FM combustion system to a light duty passenger car engine. Consideration is given to the critical design parameters associated with the application of the FM system to a multi-cylinder gasoline based engine and how the criteria can be met. Details of the design and construction of a single cylinder derivative of the multi-cylinder engine are given.

In 1961 the Consumers’ Association in Britain set up a car test unit, and in 1962 the first car test reports were published. These later became the ‘Motoring Which?’ quarterly supplement to ‘Which?’ magazine. The methods and general sequence of the CA car testing procedure are first outlined. The Human Factors contribution to this testing programme is then described. The contribution broadly takes two forms. First, human factors reference data and guidance are provided to assist with the planning and interpretation of the objective measurement programme run by the test unit. Second, an extensive Human Factors Questionnaire (HFQ) programme is organised, and the results are reported, quarterly for every group of test cars. The initial planning of the Human Factors contribution is described; then the essential features of the HFQ programme, and its successive stages of development over the years to the current form with computerised analysis and output are reviewed.

Regulated emissions from four current production European vehicles were measured over the Common Artemis Driving Cycles (CADC). Particulate Mass and Particle Number measurements were made in accordance with the newly-developed draft Particulate Measurement Programme (PMP) developed for the UN-ECE's expert group on pollution and energy (GRPE). During the test programme measurements were also made of currently non-regulated emissions including PAHs and speciation of the particulate material and key hydrocarbons. CADC results are presented for each of the four vehicles tested (one conventional gasoline vehicle, two different types of diesel without Diesel Particulate Filter (DPF) and one diesel with DPF) with results measured on the regulated New European Driving Cycle (NEDC) test for comparison. The emissions results on the Artemis cycles showed some significant differences from those on the regulated (NEDC) test cycle.

The method of flame ionization was used for measuring total hydrocarbons in both single-cylinder and multicylinder 4-cycle, direct injection diesel engine exhaust. Use of the emission parameters of hydrocarbon concentration, per cent unburned fuel, specific hydrocarbon rate, mass of hydrocarbons per million cycles, mass of hydrocarbons per mile, and mass of hydrocarbons per ton-mile are discussed. The basic approach used in the flame ionization detector is shown. The hydrocarbon sample was transferred from the exhaust system through a heated sample line and oven operating at 375 F. The sample line was aspirated to reduce the sample residence time to 2 sec. The effect various sampling locations have on hydrocarbon measurements from a single-cylinder engine is shown and discussed. The effects of load, speed, and injection timing on hydrocarbon emission data are shown for a single-cylinder engine.

Carburetor repeatability at idle was investigated both on the carburetor precision flow stand and on a chassis dynamometer equipped with exhaust emission test equipment. It was determined that some factors which significantly affect idle fuel flow repeatability on the carburetor test stand are: 1 Surface roughness of mating parts in the fuel bowl inlet system. 2 Inlet valve eccentricity. 3 Hydraulic shock in the fuel supply circuit. In addition, vehicle testing had demonstrated that carbon monoxide changes at idle may occur with constant fuel-air ratio due to changes in fuel temperature. Cycle tests have also shown a relationship between fuel temperature and carbon monoxide levels.

For 1974, Ford Motor Company is providing, as standard equipment, a solid state ignition system on all 400 CID and 460 CID engines as well as on all California vehicles equipped with 200 through 351 CID engines. This paper explains the Ford solid state ignition system and the objectives and design philosophy that was used in the development of the system. Further, a review of the design and production validation test plans is discussed. With this background, specific examples of the effectiveness of complete problem analysis for fundamental cause and corrective action is presented in addition to control methods and evaluation of corrective action. This problem analysis system allowed this automotive electronic product to go into production with a high degree of confidence in meeting the reliability goals.

The extensive use of rotative machines in the diverse branches of the modern world has made the rising undesirable mechanical and acoustic vibration levels to be a problem of special importance for the machines normal operation as for the communities that are each time more affected by the problem. It makes the study of vibration and acoustic phenomena also to be even more important and the applications of its concepts more sophisticated. Several are the concepts used for decreasing vibration levels, like common dampers, hydraulic dampers, active dampers, natural frequencies changes and others. The choice of use of one or another depends greatly on the engineering possibilities (weight, energy, physical space, other components functional interference, vibration levels, etc.) as well as the cost of implementation of each one.

This paper discusses the use of electromechanical devices as the kinematic portions of a microprocessor based gas turbine control system. Specific applications are: 1. An electric motor driven, positive displacement pump, which provides metered high pressure fuel to the distribution manifold. Fuel metering to be provided by varying the motor angular velocity. 2. An electric motor driven lube oil pump. 3. Electromechnical actuators for motion and control of compressor and power turbine variable geometry. 4. A starter/generator integral with the gas generator. Topics covered include: Comparison to conventional hydro-mechanical systems. Response characteristics of the fuel pump and actuator systems. Brushless D.C. motor characteristics. Power electronics requirements for brushless D.C. motors. Control electronics interface with brushless D.C. motor systems. Reliability and maintainability issues. Diagnostic/prognostic enhancements.

This is an overview of air bag injuries, a review of the literature and descriptions of air bag related injuries to the various body areas. Some unusual injuries are also included. The cases presented are from the author's files and one from the Special Studies Division of NHTSA.

This essay presents a brief history of aviation security measures, including problems exploited by terror attacks such as those of September 11th. Recent policy modifications are also discussed. Finally, conclusions are drawn and rationally developed into a policy proposal for developing a more secure system of domestic aviation transportation.

A new method for the structural study of long hydraulic cylinders has been developed. The rational analysis, taking cognizance of most known conditions and disturbances, is capable of an iterative type solution by computer. Some examples of its use are given, illustrating the effects of stroke length and mounting position on stresses, deflections, internal bearing loads, and critical axial load.

In one of the fatigue tests for wet friction materials, “bump test”, an inertia-type rig equipped with a multi-disk assembly is used. One of the steel disks in the assembly has radial bumps for the purpose of creating high local contact pressure and high temperature. Due to the severe contact conditions, a comparative testing for different friction materials can be conducted within a relatively small number of cycles. In the paper, a design of a “bump” assembly used for automotive wet friction materials is described. Based on both experimental tests and advanced contact modeling, non-uniform contact pressure generated by the bumps and resulting temperature are estimated. The computational model is used then to study the influence of the modulus of elasticity of the friction material and reaction plate thickness on the contact conditions. The bump fatigue tests lead ultimately to material failure.

Ammonia is one of the most useful compounds that react with NOx selectively on a catalyst, such as V2O5-TiO2, under oxygen containing exhaust gas. However ammonia cannot be stored because of its toxicity for the small power generator in populated areas or for the diesel vehicles. A new concept for NOx reduction in diesel engine using ammonia is introduced. This system is constructed from the hydrogen generator by fuel reformer, the ammonia synthesizer, SCR catalyst for NOx reduction and the gas injection system of reformed gas into the cylinder. Experimental results show that, the SCR catalyst provides a very high rate of NOx reduction, reformed gas injection into cylinder is very effective for particulate reduction. WHEN CONSIDERING INTERNAL COMBUSTION ENGINES of the 1990's the question of how to harmonize the engine with the natural environments is one of the greatest problems. The internal combustion engine changes a substance into energy via its explosive combustion.

In current competitive automobile sector, gear shift quality has become significant factor for vehicle evaluation. OEMs are sensibly focusing on improving gear shift quality to meet customer’s expectations. Though there are different gear shifting habits in different drivers, diagonal shifting is the fastest way of shifting gears in manual transmission vehicle. So the components linked with shift system should be designed to facilitate smooth diagonal gear shift pattern. This paper enlightens the process of defining chamfers on internal gear shifting components for smooth diagonal shifting movement of gear shift lever. It is hard to define chamfers by analytical or practical approach. Creo-mechanism is very useful simulation tool which can be used to understand diagonal shift patterns and to define the chamfers.

A new truck type street sweeper has been developed which incorporates some of the sweeping advantages of a three wheeled sweeper (tricycle steer) and the transport advantages of a legal highway truck. It offers major productivity improvements through better operator environment and decrease of nonsweeping time in the operational cycle. It is possible for a small “short line” special purpose vehicle manufacturer to develop, test, and produce such a vehicle and meet Federal regulatory requirements with limited “In house” design and testing facilities. Here this was accomplished through judicious augmentation by outside specialized design and testing organizations.